MSK-AFA-DS300-LD Vertical Double-Side Roll-to-Roll Coater for Battery Electrodes with Max 260mm Coating Width and Precise Blade Coating
The MSK-AFA-DS300-LD is engineered to meet the demands of producing double-sided electrode coatings for advanced battery technologies such as lithium-ion, graphene thin films, ceramic coatings, NiMH, and Ni-Zn batteries. Its vertical roll-to-roll design enables efficient processing of foam and mesh-type substrates, which are commonly used in battery electrode fabrication. The compact footprint of the system allows it to fit conveniently in laboratory environments where space is limited.
This coater employs a blade coating method that delivers high precision in coating thickness, with a typical tolerance of ±5 micrometers depending on the coating material properties. The maximum substrate width accommodated is 280 mm, with a maximum coating width of 260 mm to allow for edge clearance. The system includes an automatic alignment device to maintain coating accuracy within ±0.2 mm, ensuring uniform application across the substrate width.
Wichtigste Merkmale
- Vertical roll-to-roll configuration optimized for double-sided electrode coating.
- Blade coating technique with thickness precision of ±5 µm and coating thickness range from 3 to 50 µm.
- Maximum coating width of 260 mm on substrates up to 280 mm wide.
- Coating speed up to 800 mm/min for efficient processing.
- Integrated infrared (IR) drying system with adjustable venting and temperature control up to 120°C ±1°C.
- Automatic alignment system to maintain coating straightness within ±0.2 mm.
- Supports substrates with reeling/unreeling shafts of 75 mm inner diameter and maximum roll diameter of 300 mm.
Technische Daten
| Parameter | Spezifikation |
|---|---|
| Stromversorgung | AC 208-240 V, 50/60 Hz, Single Phase (110 V available via 3 kW transformer) |
| Stromverbrauch | 2 kW (requires 15A air breaker) |
| Coating Method | Blade Coating |
| Coating Thickness Precision | ±5 µm (material dependent) |
| Coating Thickness Range | 3 – 50 µm (wet thickness) |
| Maximum Roller Width | 300 mm (max substrate width 280 mm) |
| Maximum Coating Width | 260 mm |
| Maximum Coating Speed | 800 mm/min |
| Wire Rod Dimensions | Diameter 10 mm, Length 400 mm |
| Drying Method | Infrared (IR) heating |
| Drying Zone Length | 425 mm |
| Maximum Heating Temperature | 120°C ±1°C |
| Ventilation Capacity | Up to 403 m³/h |
| Reeling/Unreeling Shaft Diameter (I.D.) | 75 mm |
| Max Reeling/Unreeling Diameter (O.D.) | 300 mm |
| Exhaust Port Size | 127 mm O.D. |
| Compressed Air Requirement | 0.5-0.8 MPa (air compressor not included) |
| Zertifizierungen | CE Certified; NRTL (UL61010) or CSA available on request |
Typische Anwendungsbereiche
This coater is ideal for fabricating double-sided electrodes used in lithium-ion batteries, nickel-metal hydride (NiMH), nickel-zinc (Ni-Zn), graphene thin films, and ceramic coatings. It is particularly suited for coating foam and mesh substrates that require precise and uniform application of electrode materials.
Hinweise zur Konfiguration und zum Betrieb
Optional accessories include slurry pumps for continuous feeding of coating material to enable longer coating runs. Users should ensure compressed air supply within specified pressure range and install a two-stage pressure regulator if using gas cylinders to maintain safe operation. The system’s drying zone uses infrared heating with adjustable venting to optimize drying conditions for various coating materials.
